Bend Fittings - American Ductile Iron Pipe

Bends

AMERICAN Ductile Iron Fastite®, Flex-Ring®, and Lok-Ring® Fittings
ANSI/AWWA C153/A21.53* and AMERICAN Standard

90° Bends (1/4th)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

   Fastite Bell-Bell**^^

  Flex-Ring Bell-Bell**^^

  Lok-Ring Bell-Bell**

ADIP Table No. 4-4

Size in.	Pressure+ Rating psi	Dimensions in Inches			Weight in Pounds
Size in.	Pressure+ Rating psi	T	A	R	Fastite	Flex-Ring	Lok-Ring
4	350	0.34	4	3	32	50	-
6	350	0.36	5	4	48	75	-
8	350	0.38	6.5	5.38	72	105	-
10	350	0.4	7.5	6.25	109	165	-
12	350	0.42	9	7.5	142	215	-
14	350	.47++	14	11.5	231	425	-
16	350	.50++	15	12.5	277	515	-
18	350	0.75	16.5	14	565	720	-
20	350	0.8	18	15.5	680	815	-
24	350	0.61	17	15.5	760	760	-
30	250	0.66	22.75	20.5	1290	1290	-
36	250	0.74	25.75	23.5	1810	1810	-
42	250	0.82	29.25	26.5	3015^	2784	-
48	250	0.9	33.25	30.5	4120^	-	3145
54	250	0.9	37	34.25	3750	-	3930
60	250	0.94	39.5	36.5	4390	-	4620
64	250	0.99	42	38.75	5170	-	5385

Notes:
*AWWA C153 configurations with shorter center-to-socket dimensions, etc. may be furnished in some cases in the 14"-20" size range. Check AMERICAN if dimensions are critical.
**18" and larger Fastite and 14" and larger Flex-Ring and Lok-Ring 90° Bends may be furnished with Fastite Plain Ends, Flex-Ring Ends, or Lok-Ring Ends. See Table No. 4-2.
+ Higher pressure ratings are available on special applications. Pressure ratings may be limited below the values shown by the pressure rating of the pipe to which fitting is attached, or the restrained joint used.
Based on performance testing per AWWA C153, AMERICAN can rate 30"-48" C153 bends 350 psi. Check AMERICAN.
See General Notes.
++ 14" and 16" Flex-Ring fittings may have greater "T" dimensions than those shown.
^ Fastite fittings with these weights have different dimensions than are shown in this table. Contact AMERICAN when dimensions are critical.
^^ 24"-36" Fastite and Flex-Ring C153 bends have the same appearance (both have basic cross-section of top middle "cut").

60° Bends (1/6th)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

   Fastite Bell-Bell**

   Flex-Ring Bell-Bell**

   Lok-Ring Bell-Bell**

ADIP Table No. 4-5

Size*** in.	Pressure+ Rating psi	Dimensions in Inches			Weight in Pounds
Size*** in.	Pressure+ Rating psi	T	A	R	Fastite	Flex-Ring	Lok-Ring
30	250	1.03	15	19.9	1415	1585	-
36	250	1.15	28	42.4	2780	2895	-
42	250	1.28	31	42.5	3315	-	-
48	250	1.42	24	35.5	3505	-	3700
54	250	0.9	24	36.8	3115	-	3295
60	250	0.94	24	36.4	3495	-	3720
64	250	0.99	30	46.3	4520	-	4740

Notes:
*AWWA C153 configurations with lesser weights and dimensions may be furnished in some sizes. Check AMERICAN.
**Fastite, Flex-Ring, and Lok-Ring Bends may be furnished with Fastite Plain Ends, Flex-Ring Ends, or Lok-Ring Ends. See Table No. 4-2.
***Smaller sizes are available on special applications. Check AMERICAN.
+ Higher pressure ratings are available on special applications. Check AMERICAN.
See General Notes.

45° Bends (1/8th)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

   Fastite Bell-Bell**^^

   Flex-Ring Bell-Bell**^^

   Lok-Ring Bell-Bell**

ADIP Table No. 4-6

Size in.	Pressure+ Rating psi	Dimensions in Inches			Weight in Pounds
Size in.	Pressure+ Rating psi	T	A	R	Fastite	Flex-Ring	Lok-Ring
4	350	0.34	2	2.41	27	-	-
6	350	0.36	3	4.83	40	-	-
8	350	0.38	3.5	5.75	59	-	-
10	350	0.4	4.5	7.85	88	-	-
12	350	0.42	5.5	9.66	117	-	-
14	350	.47++	7.5	12.06	177	-	-
16	350	.50++	8	13.25	210	425	-
18	350	0.75	8.5	14.5	445	595	-
20	350	0.8	9.5	16.88	530	665	-
24	350	0.61	7.5	14.5	620	620	-
30	250	0.66	10.5	19.92	1010	1010	-
36	250	0.74	12	23.54	1395	1395	-
42	250	0.82	14	27.2	2560^	2235	-
48	250	0.9	15	29.6	3605^	-	2245
54	250	0.9	20.28	42.32	2890	-	3070
60	250	0.94	21.26	44.08	3335	-	3560
64	250	0.99	22.24	45.85	3865	-	4085

Notes:
*AWWA C153 configurations with shorter center-to-socket dimensions, etc. may be furnished in some cases in the 14"-20" size range. Check AMERICAN if dimensions are critical.
**18" and larger Fastite and 14" and larger Flex-Ring and Lok-Ring 45° Bends may be furnished with Fastite Plain Ends, Flex-Ring Ends, or Lok-Ring Ends. See Table No. 4-2.
+Higher pressure ratings are available on special applications.
Based on performance testing per AWWA C153, AMERICAN can rate 30"-48" C153 bends 350 psi. Check AMERICAN.
++ 14" and 16" Flex-Ring fittings may have greater "T" dimensions than those shown.
See General Notes.
^ Fastite fittings with these weights have different dimensions than are shown in this table. Contact AMERICAN when dimensions are critical.
^^ 24"-36" Fastite and Flex-Ring C153 bends have the same appearance (both have basic cross-section of top middle "cut").

30° Bends (1/12th)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

   Fastite Bell-Bell**

   Flex-Ring Bell-Bell**

   Lok-Ring Bell-Bell**

ADIP Table No. 4-7

Size*** in.	Pressure+ Rating psi	Dimensions in Inches			Weight in Pounds
Size*** in.	Pressure+ Rating psi	T	A	R	Fastite	Flex-Ring	Lok-Ring
30	250	1.03	15	42.9	1455	1630	-
36	250	1.15	18	54.1	2210	2335	-
42	250	1.28	21	65.3	2610	-	-
48	250	0.90	11	30.79	3670^	-	1980
54	250	0.90	16	49.4	2585	-	2765
60	250	0.94	19	59.7	3180	-	3405
64	250	0.99	18.5	56.9	3545	-	3760

Notes:
*AWWA C153 configurations with lesser weights and dimensions may be furnished in some sizes. Check AMERICAN.
**Fastite, Flex-Ring, and Lok-Ring Bends may be furnished with Fastite Plain Ends, Flex-Ring Ends, or Lok-Ring Ends. See Table No. 4-2.
***Smaller sizes are available on special applications. Check AMERICAN.
+Higher pressure ratings are available on special applications. Check AMERICAN.
See General Notes.
^Fastite fittings with these weights have different dimensions than are shown in this table. Contact AMERICAN when dimensions are critical.

22 1/2° Bends (1/16th)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

   Fastite Bell-Bell**^^

   Flex-Ring Bell-Bell**^^

   Lok-Ring Bell-Bell**

ADIP Table No. 4-8

Size in.	Pressure+ Rating psi	Dimensions in Inches			Weight in Pounds
Size in.	Pressure+ Rating psi	T	A	R	Fastite	Flex-Ring	Lok-Ring
4	350	0.34	1.5	2.51	26	-	-
6	350	0.36	2	5.03	37	-	-
8	350	0.38	2.5	6.94	54	-	-
10	350	0.4	3	8.8	78	-	-
12	350	0.42	3.5	10.05	100	-	-
14	350	.47++	7.5	25.12	158	-	-
16	350	.50++	8	27.62	185	430	-
18	350	0.75	8.5	30.19	450	600	-
20	350	0.8	9.5	35.19	540	670	-
24	350	0.61	4.5	15.1	525	525	-
30	250	0.66	6.75	22.6	900	900	-
36	250	0.74	7.75	27.7	1220	1220	-
42	250	0.82	9	31.4	2625^	1972	-
48	250	0.9	10	36.5	3695^	-	1915
54	250	0.9	10.24	37.65	2125	-	2305
60	250	0.94	10.63	38.36	2425	-	2650
64	250	0.99	11.02	39.06	2785	-	3000

Notes:
*AWWA C153 configurations with shorter center-to-socket dimensions, etc. may be furnished in some cases in the 14"-20" size range. Check AMERICAN if dimensions are critical.
** 18" and larger Fastite and 14" and larger Flex-Ring and Lok-Ring 22 1/2 ° Bends may be furnished with Fastite Plain Ends, Flex-Ring Ends, or Lok-Ring Ends. See Table No. 4-2.
+Higher pressure ratings are available on special applications.
Based on performance testing per AWWA C153, AMERICAN can rate 30"-48" C153 bends 350 psi. Check AMERICAN.
++ 14" and 16" Flex-Ring fittings may have greater "T" dimensions than those shown.
See General Notes.
^ Fastite fittings with these weights have different dimensions than are shown in this table. Contact AMERICAN when dimensions are critical.
^^ 24"-36" Fastite and Flex-Ring C153 bends have the same appearance (both have basic cross-section of top middle "cut").

11 1/4° Bends (1/32nd)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

   Fastite Bell-Bell**^^

   Flex-Ring Bell-Bell**^^

   Lok-Ring Bell-Bell**

ADIP Table No. 4-9

Size in.	Pressure+ Rating psi	Dimensions in Inches			Weight in Pounds
Size in.	Pressure+ Rating psi	T	A	R	Fastite	Flex-Ring	Lok-Ring
4	350	0.34	1.25	2.54	25	-	-
6	350	0.36	1.5	5.08	34	-	-
8	350	0.38	1.75	6.4	50	-	-
10	350	0.4	2	7.61	71	-	-
12	350	0.42	2.25	7.61	89	-	-
14	350	.47++	7.5	50.75	130	-	-
16	350	.50++	8	55.81	165	430	-
18	350	0.75	8.5	60.94	450	605	-
20	350	0.8	9.5	71.06	540	675	-
24	350	0.89	3.0	15.33	490	490	-
30	250	0.66	4.75	25.4	830	830	-
36	250	0.74	5	27.9	1100	1100	-
42	250	0.82	6	33	2640^	1934	-
48	250	0.9	6.5	33.5	3720^	-	1630
54	250	0.9	6.5	38.07	1820	-	2000
60	250	0.94	7	40.61	2095	-	2320
64	250	0.99	7	38.07	2375	-	2590

Notes:
*AWWA C153 configurations with shorter center-to-socket dimensions, etc. may be furnished in some cases in the 14"-20" size range. Check AMERICAN if dimensions are critical.
**18" and larger Fastite and 14" and larger Flex-Ring and Lok-Ring 11 1/4° Bends may be furnished with Fastite Plain Ends, Flex-Ring Ends, or Lok-Ring Ends.
See Table No. 4-2.
+Higher pressure ratings are available on special applications.
Based on performance testing per AWWA C153, AMERICAN can rate 30"-48" C153 bends 350 psi. Check AMERICAN.
++ 14" and 16" Flex-Ring fittings may have greater "T" dimensions than those shown.
See General Notes.
^ Fastite fittings with these weights have different dimensions than are shown in this table. Contact AMERICAN when dimensions are critical.
^^ 24"-48" Fastite and Flex-Ring C153 bends have the same appearance (both have basic cross-section of top middle "cut").

5 5/8° Bends (1/64th)

90° | 60° | 45° | 30° | 22-1/2° | 11-1/4° | 5-5/8° | Back To Top

Lok-Ring Bell-Bell**

ADIP Table No. 4-10

Size in.	Pressure Rating psi	Dimensions in Inches			Weight
Size in.	Pressure Rating psi	T	A	R	lb
48	250	0.90	5.0	45.78	1555
54	250	0.90	6.5	76.33	2000
60	250	0.94	6.5	71.24	2275
64	250	0.99	7.0	76.33	2590

Notes:
**Lok-Ring 5 5/8° Bends may be furnished with Lok-Ring Ends. See Table No. 4-2.
See General Notes.

> 90°
> 60°
> 45°
> 30°
> 22-1/2°
> 11-1/4°
> 5-5/8°

Bends

AMERICAN Ductile Iron Fastite®, Flex-Ring®, and Lok-Ring® FittingsANSI/AWWA C153/A21.53* and AMERICAN Standard

AMERICAN Ductile Iron Fastite®, Flex-Ring®, and Lok-Ring® Fittings
ANSI/AWWA C153/A21.53* and AMERICAN Standard