Dimensions, Weights, and Short Lengths

ADIP Table No. 8-4

Notes:
Hub diameter and length are AMERICAN Design. See Table No. 8-3 for data on bolt holes and bolt circle.
When ordering Companion Flanges for Ductile Iron Pipe specify the outside diameter of the pipe.
"X" and "Y" dimensions may vary depending on foundry equipment.

Flange and Flange

ADIP Table No. 8-5

Notes:
*Pressure rating designated is maximum water working pressure. Contact AMERICAN on higher pressure requirements.
**Check AMERICAN if longer or shorter lengths required.
+This rating is only applicable to flanged joints utilizing AMERICAN Toruseal® gaskets as per Flanged Pipe description.
Pipe is available with greater wall thickness than shown. Thicknesses above correspond to Special Class 53 for 4"-54" diameters, and Pressure Class 350 for 60" and 64" diameters as shown in AWWA C151.
Any length between minimum and maximum shown can be furnished.
Tolerance on length is ±0.12 in.
Standard drilling is with bolt holes aligned, straddling a common centerline. Special drilling can be furnished on request.
Where required, specify flanges "Tap for Studs."
The bolt circle and bolt holes of AWWA C115 flanges, AWWA C110 flanges and ANSI B16.1 Class 125 flanges are identical, and these flanges can be joined. AWWA C115 and AWWA C110 flanges are rated for 250-350 psi water working pressure depending on size and specified gasketing system.

ADIP Table No. 8-6

Notes:
*Pressure rating designated is maximum water working pressure. Contact AMERICAN on higher pressure requirements.
**Check AMERICAN if longer or shorter lengths required. All minimum lengths assume a "no-gauge" plain end (no joint will be made at the plain end).
+This rating is only applicable to flanged joints utilizing AMERICAN Toruseal® gaskets as per Flanged Pipe description.
Plain ends to be assembled in a joint (MJ, Fastite, coupling, etc.) must be ordered gauged for the specific joint.
Pipe is available with greater wall thickness than shown. Thicknesses above correspond to Special Class 53 for 4"-54" diameters, and Pressure Class 350 for 60" and 64" diameters as shown in AWWA C151.
Any length between minimum and maximum shown can be furnished.
Tolerance on length is ±0.25 in.
Where required, specify flanges "Tap for Studs."
The bolt circle and bolt holes of AWWA C115 flanges, AWWA C110 flanges and ANSI B16.1 Class 125 flanges are identical, and these flanges can be joined. AWWA C115 and AWWA C110 flanges are rated for 250-350 psi water working pressure depending on size and specified gasketing system.

ADIP Table No. 8-7

Notes:
*Pressure rating designated is maximum water working pressure. Contact AMERICAN on higher pressure requirements.
**Check AMERICAN if longer or shorter lengths required.
+This rating is only applicable to flanged joints utilizing AMERICAN Toruseal® gaskets as per Flanged Pipe description.
14"-64"pipe is not available with integrally cast MJ Bell. See Table 8-8 (below) for Flange and Fastite Pipe.
Pipe is available with greater wall thickness than shown. Thicknesses above correspond to Special Class 53.
Any length between minimum and maximum shown can be furnished.
Tolerance on length is ±0.25 in.
If specified, bolt holes both ends can be drilled, straddling a common centerline.
Where required, specify flanges or MJ Bells "Tap for Studs."
The bolt circle and bolt holes of AWWA C115 flanges, AWWA C110 flanges and ANSI B16.1 Class 125 flanges are identical, and these flanges can be joined. AWWA C115 and AWWA C110 flanges are rated for 250-350 psi water working pressure depending on size and specified gasketing system.

ADIP Table No. 8-8

Notes:
*Pressure rating designated is maximum water working pressure. Contact AMERICAN on higher pressure requirements.
**Check AMERICAN if longer or shorter lengths required.
+This rating is only applicable to flanged joints utilizing AMERICAN Toruseal® gaskets as per Flanged Pipe description.
Pipe is available with greater wall thickness than shown. Thicknesses above correspond to Special Class 53 for 4"-54" diameters, and Pressure Class 350 for 60" and 64" diameters as shown in AWWA C151.
Any length between minimum and maximum shown can be furnished.
Tolerance on length is ±0.25 in.
Where required, specify flanges "Tap for Studs."
The bolt circle and bolt holes of AWWA C115 flanges, AWWA C110 flanges and ANSI B16.1 Class 125 flanges are identical, and these flanges can be joined. AWWA C115 and AWWA C110 flanges are rated for 250-350 psi water working pressure depending on size and specified gasketing system.

ADIP Table No. 8-12

Notes:
Flanges faced and drilled per ANSI B16.1 Class 250 have a 0.06" raised face; they do not match AWWA C110 or C115 flanges.
Flanges may be furnished with a flat face upon special request.
Hub diameter and length are AMERICAN Design. See Table No. 8-11 (short lengths) for data on bolt holes and bolt circle.
When ordering Companion Flanges for Ductile Iron Pipe specify the outside diameter of the pipe.

ADIP Table No. 8-13

Notes:
*The minimum lengths shown may not allow clearance in all cases for installation of bolts between flanges requiring bolt clearance from the other direction. Very short (shorter than the minimums as per above table) fabricated steel adapters are also available for connecting AWWA C115 flanged pipe or AWWA C110 fittings to ANSI B16.1 Class 250 flanged items. Contact AMERICAN for details.
Pressure rating designated is maximum water working pressure.
Flanges faced and drilled per ANSI B16.1 Class 250 have 0.06" raised face; they do not match AWWA C110 or C115 flanges. Flanges may be furnished with a flat face upon special request.
Pipe is available with greater wall thickness than shown.
Tolerance on length for Flange and Flange pipe is ±0.12 in.
Standard drilling is with bolt holes aligned, straddling a common centerline. Class 250 is special drilling and all connecting equipment must have flanges faced and drilled per ANSI B16.1 Class 250.
Where required, specify flanges "Tap for Studs."